Mikrotik:Bandwidth scheduling

The Limit of Different Bandwidth In Day and Night will be manged by Mikrotik according to your
requirement .As you have seen there are most of the person are configuring their bandwidth
scheduling on various types .

There are lot many ways to limit bandwidth for day and Night, but personally I found this is the easiest way, Here it is.

I have used Simple Queue, Script and Scheduler.

Suppose we have one network 192.168.20.0/24 and want to limit Bandwidth for day and Night Time.

My LAN Network 192.168.20.0/24

Bandwidth = 06:00am – 18:00pm – 1Mbps. <Max-Limit>
Bandwidth = 18:00pm – 06:00am – 2Mbps. <Max-Limit>

Create two simple queues for the same network with different Bandwidth Limit.

/queue simple
#name=”Day” target-addresses=192.168.20.0/24 dst-address=0.0.0.0/0
interface=<ether-x> parent=none direction=both priority=8
queue=default-small/default-small limit-at=512k/512k
max-limit=1M/1M total-queue=default-small

#name=”Night” target-addresses=192.168.20.0/24 dst-address=0.0.0.0/0
interface=<ether-x> parent=none direction=both priority=8
queue=default-small/default-small limit-at=1M/1M
max-limit=2M/2M total-queue=default-small
Now, write scripts

/system script
#name=”Day” source=/queue simple enable Day; /queue simple disable Night
#name=”Night” source=/queue simple enable Night; /queue simple disable Day
Finally, Schedule it

/system scheduler
#name=”Day” on-event=Day start-date=oct/13/2007 start-time=06:00:00 interval=1d
#name=”Night” on-event=Night start-date=oct/13/2007 start-time=18:00:00 interval=1d


The configuration is simple and based on your requirement you can make change the rule little bit .But here I am not making it different any way and the way of configuration will be same as above .

Mikrotik:-EoIP in Mikrotik

Eoip is a layer 2 mechanism which is called as Ethernet over IP.

At this time I will share again about the material mikrotik, and still the same as before, this time we will still discuss about tunneling. The tunneling we will be using at this time, is the EoIP tunnel. EoIP itself, is a tunneling that works on layer2 that connects a network with other networks

For your own security, EoIP has very low security, because EoIP does not encrypt the packets sent via EoIP. But for its benefit, EoIP can connect the same network even in different areas.

Configuration

For configuration, of course, first configure ip address for the interface that will be used. For the ip address itself, make the local network R1 and R2 are in the same network because we will create an EoIP tunnel that works based on Layer 2. Next, configure EoIP on the router.


[admin @ R1]> / eoip interface
add local-address = 12.12.12.1 name = eoip1 remote-address = 12.12.12.2 tunnel-id = 10
[admin @ R2]> / interface eoip
add local-address = 12.12.12.2 name = eoip1 remote-address = 12.12.12.1 tunnel-id = 10

Based on the above configuration, we only need to define the local address and remote address of the router that wants to make tunneling. Then for the tunnel id, it will provide an identity for the tunneling made that the tunneling used is only for those using tunnel id 10. Next, configure the bridge.

[admin @ R1]> / interface bridge
add name = eoip
[admin @ R1]> / interface bridge port
add bridge = eoip interface = ether1
add bridge = eoip interface = eoip1

[admin @ R2]> / interface bridge
add name = eoip
[admin @ R2]> / interface bridge port
add bridge = eoip interface = ether1
add bridge = eoip interface = eoip1

Based on the above configuration, we create the eoip interface that has been dbuat earlier, "ter-bridge" with the interface to the local network that we have. This is because EoIP works on layer 2. So that the client router can connect with other routers, we only need to do the bridge configuration with the existing eoip interface on the router. If so, verify.